Whirlpool Icemaker Repair Guide In this Whirlpool icemaker repair guide I will walk you through the steps in repairing Whirlpool icemakers with the module motor as shown in the picture below. Power is applied for approximately 7-9 seconds during the harvest cycle and energizes the solenoid on the valve to allow water to flow. This photo shows my old bucket now attached to the new ice maker with the newer but larger bucket next to it: Comparing motors side-by-side The units look identical except for the sticker placement , but I like to tell myself that they hopefully found a better motor supplier and that this ice maker will last more than seven years. Over time, the filter may become restricted and reduce the water flow to the ice maker, causing a symptom of little or no ice. When it is locked in the upper position, it shuts off the ice maker. Whirlpool Refrigerator Troubleshooting Tired of reading complex thermodynamic theory in a Whirlpool refrigerator manual? With a dampened microfiber cloth wrapped around a thin piece of wood, such as a chopstick, clean in the corners and hard to reach areas.
If the ice has unusual taste or is gray, install a filter to clear out any minerals present. Note that if you are taking air temperature, the door of the freezer should be closed for at least 30 minutes before reading temperature. Are you in need of an ice maker repair? To check this first, disconnect power from the refrigerator then slide the icemaker out without unplugging it and remove the cover off the front of the icemaker. The fill valve sends water through a fill tube into a mechanized ice maker assembly that includes an ice mold. Whirlpool Icemaker Repair-Optics Test In this section of this Whirlpool icemaker repair guide I will walk you though diagnosing the ice level optics on Whirlpool refrigerators with the ice-bin mounted in the door. If all of this happens the thermostat inside the icemaker is bad provided the temperature inside the freezer is ok.
If the water pressure is sufficient, use a multimeter to check for power to the water inlet valve. I will also discuss the procedure for diagnosing the ice level control optics for whirlpool refrigerators with the ice bin mounted on the freezer door. Place one end of the jumper wire in the hole marked H and the other end in the hole marked T. We've identified the most common parts that can cause a refrigerator's ice maker to not make ice, but there are other parts that could be at fault. Behind the cover is a series of electrical test points that can be used to diagnose the ice maker.
If none of these parts are at fault, and the freezer temperature is at least 15 degrees Fahrenheit, replace the ice maker assembly. If the door fails to close completely or fails to open in a normal way, check the bins and shelves. Most filters contain and are made up of carbon and fabric filter. I mean, who sells a used ice maker on Amazon? Something as easy as checking a water line, replacing a filter, or setting an On-Off switch to On may solve ice maker woes and bring it to full functioning order. If when you do this the icemaker dumps the ice in the mold and the feeler arm lifts up and then back down, the thermostat inside the icemaker is bad provided the temperature in the freezer is ok. When the ice level drops below the beam, the control board signals the ice maker to make more ice.
When inserted into the test points for 5 to 10 seconds, the motor should start and the cycle will continue on its own. This should power up the water valve and water should enter the icemaker. Here are a few steps you can take to get your ice maker working. You can normally follow the inlet tubing from the ice maker back to the valve. This icy water can then freeze on the stripper during the next cycle causing an ice bridge.
Searching with your model number will give you access to all parts and schematics, symptoms for your specific refrigerator as well as all installation instructions and videos. Once you select a symptom, RepairClinic. Replace the valve with a wider version to allow more water to reach the ice maker. ©Don Vandervort, HomeTips Make sure the bail wire above the ice collection drawer is not locked in its upper position. Then it turns on a small that rotates the ice ejection arm. Using a little white vinegar for cleaning kills mold and disinfect while at the same time being safe to use around food. Our Whirlpool refrigerator repair manual cuts out all the unnecessary theory and sealed system repairs that the novice will never perform.
The ice maker switch might be defective. Note to be certin that the jumper stays in place or the test will fail. The freezer temperature should be set between 0 and 5 degrees Fahrenheit -18 to -15C for the ice maker to work properly. Refrigerator Repair Help To get refrigerator repair help and refrigerator troubleshooting advice, enter your model number in the search box below. If you find that the refrigerator is not cooling properly Special note for bottom freezers the icemaker may not respond to the jumper wire test described below unless you close the door or press the door switch. Find which Whirlpool fridge parts in your machine need replacing and how to do it yourself.
To determine if the thermostat is defective, use a multimeter to test it for continuity. Once the desired product is identified, read the full description of the listing. Also note on these models only try to jump out T to H. If there is water leaking from the back of the refrigerator, replace the water supply line and reinforce the connection point with Teflon tape. If there are no cubes or very small cubes, then you should look for issues with the water fill system. If when you do this ice still will not dump, the motor modular is bad and needs replacing part number 8201515. Then after the jumper is in place plug the refrigerator back in and wait 15 seconds or so before opening the freezer door.
If you have a whirlpool refrigerator with the ice-bin mounted in the door it will not have the feeler arm, it will have an ice level control optics. If the light blinks once followed by a one second delay, the optics are bad and needs replacing. To check this icemaker you will have to make a jumper wire. Was the water system flushed after filter installation or replacement? Straighten the water source line to restore adequate water flow and pressure. But as it has so many times before, Amazon. Alternatively, online purchasing is an option for price and convenience, and eBay sellers offer a wide selection of components. The ice maker temperature must generally be lower than 20 degrees Fahrenheit for the thermostat contacts to close.
Before replacing the ice maker assembly, check the water inlet valve, water line, and fan. The last step is finding out if the ice maker has any problems and fixing them. Typical Problem Potential Solution No ice is being made at all Make sure the ice maker is on Locate switch or lever on side of ice maker or in the freezer Make sure water supply to ice maker is on with no kinks in the Water under the refrigerator may indicate a supply leak Low water pressure on supply entry or excessively low temperature may cause intake line to freeze Harness contact connection may be loose and need reseating No ice is coming out of the dispenser Dispenser lock may be on may be clogged with ice Abundance of frost in the ice chute and ice bin Likely an air leak Remove ice bin and shine a flashlight into ice chute, then check for light outside of dispenser replacement may be necessary may not be closing properly and may need replacing Bottom of freezer or bin is covered with ice Possible air leak. Let Appliance Repair Medic Services help diagnose the problem and fix your whirlpool ice maker in no time. This means the valve and the solenoid are probably okay, but the water supply is not.